PDA

View Full Version : 4'x2'x18" cage tutorial



RehabRalphy
10-12-2006, 02:35 AM
Okay guys. For those who are less fortunate with building things. I decided on the cage I'm building at the moment to make a tutorial.

Cage demotion: 48"x24"x18"
Total cost: In the $70's
Supplies that I had to buy:
1/2" MDF Plank - $15.59
32"x14" Window - $13.49
6'x9' Roll of Linoleum - $16.97
Vinyl Adhesive - $6.97
Trowel - $2.99
1" Drywall Screws - $3.82
Undereave Vent - $1.49
Supplies I had around the house (may be added to in the future):
1 gallon Bear Paint - $10
Sealant - $2.99
Screw drivers
Jig saw
1" Drill bit
Drill bits
Pliers

Supply pictures (not all supplies are shown below)

From left to right - 1" drywall screws, trowel, vinyl adhesive
user posted image
From left to right - 1" drywall screws, trowel, vinyl adhesive, undereave vent
user posted image
36"x18" Window
user posted image
user posted image
Linoleum 6'x9' roll (picture card was bad so the pictures color turned out bad)

http://img.photobucket.com/albums/v444/Reptodude/new%20boa%20cage/HPIM1118.jpg

8'x4' Plank cut into 5 pieces.
1. 48" x 24"
2. 48" x 24"
3. 48" x 18" - will be cut into 2 pieces of 24" x 18" for the sides (ends) of the cage.
4. 46" x 18"
5. 48" x 12" - scrap. Can be used for a lip in the front of the cage or a shelf inside.

http://img.photobucket.com/albums/v444/Reptodude/new%20boa%20cage/Picture013.jpg

This was only some supplies, there are still other supplies not pictured
First step in the process.
1. Before you get start, unroll the linoleum and place on a flat, hard, clean, substrate. Weight it down in order to get rid of all the roll in the sheet. Top side is best facing downward. Wait a few hours (or even 24 hours for best results) in order for it to be ready to use.
2. While the lenolium is flattening out, you can be some other things in order to get things started. On the window, you must remove the screen in order to use the window as the main entrance of the cage. You can do this by pull up the edges of the screen with a pair of pliers. Its best to removed the glass before you go yanking at the window.
3. Cut the planks of MDF into the certain measurements you want. I chose a 48" x 24" x 18" cage. Above you will find each planks measurements. You may prime the planks to start if you want. The side with where the linoleum is being placed does not need to be primed, sealed, or painted. The other side can be, but its a preference. In this order is the best way to paint the outsides of the planks. Prime once(1), paint once (1), paint twice (2), seal once (1), seal twice (2), seal three times (3, isn't needed but is nice to have).
Linoleum placement, cutting, and glueing.
Once the linoleum has flattened out, you may now start the process of glueing on the linoleum to the wood, but theres a few steps before this you have to do.

1. Line up the wood planks onto the linoleum in order to find out the best way to cut out the linoleum. Once you have found the right 'pattern' or 'puzzle' the hard process comes in.
2. Make sure to line up the edges of the flattened linoleum with the cut planks of wood. This makes sure when you cut the linoleum patterns out that you get nice even cuts. Once you have the wood lined up, trace a pencil line around the outsides of the wood. Label the wood and the linoleum pattern for future glue. (*hint: Right the number on the wood the same direction as the letter on the linoleum pattern, this way it will line up correctly when gluing)

http://img.photobucket.com/albums/v444/Reptodude/new%20boa%20cage/1-9-065.jpg

3. Take off the wood plank and set it aside. Now you can take your handy dandy cutting tool and carefully cut out the lines you drew. Its best to use a sharp blade when cutting to make the cuts even and perfect. Once you have successfully cut it out, set the cut out piece of linoleum ontop of the plank and set it aside. Once all the patterns are cut out, move to the next step.
4. Take a dry cloth and wipe all the pieces of wood and cut out pieces of linoleum really well. This way no dust or debree are on the places you will glue.
5. Time for the gluing. This can be tricking, but after the first plank and linoleum are glued, you'll get the hang of it. Trawel the glue onto the wood, then place the cut out linoleum pattern ontop of the wood. (Hints, when traweling the glue, make sure you dont get to much around the edges, this will cause oozing of the glue. Stay at least .5 of an inch away from the outsides of the wood with the glue.) Once you have layed the linoleum on top of the gluey wood, use a rolling pen to get out all the air bubbles underneath the linoleum. If any glue oozes out the sides, take a damp paper towel and whipe off the access glue. **Important: Once the glue is placed onto the wood, you only have 15 minutes in order to put on the linoleum.**
6. When all the pannels of wood are glued to the linoleum, place in an area where they will not be walked on, bumped, and make SURE they have venhilation. This is a big deal. Some glues may not smell bad, but still may have fumes. We don't want your house to go 'Ka-Boom'... Allow the glue to dry for 24 hours before the next step.

http://img.photobucket.com/albums/v444/Reptodude/new%20boa%20cage/1-9-06.jpg

http://img.photobucket.com/albums/v444/Reptodude/new%20boa%20cage/1-9-061.jpg

PUTTING TOGETHER IT ALL:
Next steps: Screw the boards together. Well This part is pretty self-explainable. Just screw them together. Remember, you can't go overbored with screws. You want this to be sturdy. Make sure you drill pilot holes.

http://img.photobucket.com/albums/v444/Reptodude/new%20boa%20cage/1-15-061.jpg

http://img.photobucket.com/albums/v444/Reptodude/new%20boa%20cage/1-15-06.jpg

Now you can drill holes for your vents. I chose to use a door hole bit. Its a big circle with teeth on it used for cutting out door knob holes. I centered the holes and it came out nice. Make sure not to go to fast when drilling it out, it will start burning the MDF if your not carefull about that.

http://img.photobucket.com/albums/v444/Reptodude/new%20boa%20cage/1-16-052.jpg

http://img.photobucket.com/albums/v444/Reptodude/new%20boa%20cage/1-16-05.jpg

Now you can line up your exterior vents to predrill holes and make sure it looks nice. Make sure to measure and center it. This way both sides will look the same.

http://img.photobucket.com/albums/v444/Reptodude/new%20boa%20cage/1-16-051.jpg

Time for caulking. Buy any type of clear sylicone caulking for sealing the inside corners and edges. Just squeeze a bead of caulk on the cracks and gently glide your finger down the caulk on the edges to make it nice and smooth. Make sure to get extra caulk in the corners so nothing can leak out there or get in there.
Lighting: Now you can install your lights. Simply drill a hole in the back of the cage around the top to thread your power cords through. You will probably have to splice the cords in order for it to fit through the small hole. Once you thread it through the hole, reconnect the cords and use electral tape on it so nothing can get to it. Mount your light fixture anywhere on the top of the inner part of the cage and thats it for that.

http://img.photobucket.com/albums/v444/Reptodude/new%20boa%20cage/1-16-053.jpg

STAINING: Nows the tricky part. Choose your prefered stain. Gently STURE (not shake) the stain in the can in order to mix it. Apply the stain to the wood with a cloth. Once the area disired is covered, whipe off the access stain with a paper towel then move to the next part of the cage. Apply more coats after 6 hours of drying time inbetween coats. Keep adding coats until the color you want appears.

http://img.photobucket.com/albums/v444/Reptodude/Picture010.jpg

SEALING/POLYURETHENE: This is the HARDEST PART. Before I start, make sure you do this in a well venhilated area! Whipe down your cage with a very very lightly watered cloth on order to remove debree. Stir the slear in the can very gently, dont allow bubbles to form when sturring. Apply a coat of this to one side at a time. Make sure the side your sealing is facing upwards so no drips accure. This will take awhile but its well worth it. You DONT want to have drips on your cage. Inbetween coats, sand off the little bumps that drys on the cage with the finest sandpaper you own. Then take a tack cloth (sold at homedepot, its a sticky cheese cloth) and whipe down the spot your apply the second or third coat too. Then apply another coat. Allow the recammended drying time between coats. 2-3 coats is best. It takes at least 2 coats in order for it to become water resistant.
Once its all dried now you may start to apply the door and vents. Since everything was pre-drilled, there wont be any hassle marking out where to put it. Just screw everything on the cage.
You may apply trim to the cage in order to cover up those edges. I have not done this yet but I will. I just have not had the time to do so. Allow the cage to "air out" for a few days so theres no fumes inside the cage.

DOOR. I used a storm window for my door. Its 36" x 18" it has little latchs on the front. Problem is the whole thing glass piece comes off. I'm sure they sell windows. I'll just add some hendges onto the frame. Before attaching the window, you have to re-enforce the MDF. This way it wont buckle on you from the weight of the window. I simply bolted on 1x2's inside. Then I screwed the window onto the 1x2's. The storm window only cost me $13 opposed to a $50 real window.

LIGHTING: I used a wire cage around my light. Secured the cage with some wood around the base of the cage. The other light bulb was taken out. Its just an open socket for back up.

http://img.photobucket.com/albums/v444/Reptodude/new%20boa%20cage/Picture012.jpg

http://img.photobucket.com/albums/v444/Reptodude/new%20boa%20cage/8429f80a.jpg

http://img.photobucket.com/albums/v444/Reptodude/new%20boa%20cage/Picture014.jpg

http://img.photobucket.com/albums/v444/Reptodude/new%20boa%20cage/808ef48f.jpg

http://img.photobucket.com/albums/v444/Reptodude/new%20boa%20cage/Picture015.jpg

This took a lot of time to build and to type up.
Hopefully it will help anyone who is having troubles with building cages.
Just remember one phrase, "Measure twice, cut once".

Thanks,
Michael

Octane
10-12-2006, 01:53 PM
BRAVO!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!


very nice i love the look i want to build 2 tanks likde this one for my ball and one for my king....... very very nice

TheNero
10-12-2006, 02:51 PM
wow this is great, awsome I was just about to start building my BBC's new cage and this is the plans and tut I will use great job

RehabRalphy
10-12-2006, 08:08 PM
I'm also thinking about using the stick on laminant tiles for the outside of the cage. I like the black marble look. To top it off after that, I plan on putting white trim on the edges on the outside. Make everything look nice.

Melinda
10-15-2006, 07:54 PM
Very nice!! This design would be fabulous for dragon's. Thank you very much for taking the time to write up the tutorial. I really like how you've put the linoleum in the whole thing. Makes cleanup so much easier.

M

gunznrosez13
11-08-2006, 03:13 AM
wow im impressed

mike
12-24-2006, 03:09 AM
nice job! :D

Broodwich
12-25-2006, 05:56 PM
Hey RehabRalphy,

Thanks a million for posting these pictures and instructions on building such a wonderful tank. I will have to use some tips you gave when making my own custom tank. DIY FOREVER :P :D

RehabRalphy
12-25-2006, 06:09 PM
Thanks, I have done some upgrades to the cage since the tutorial was made.

I added black and white marble stick on tiles to the outside of the cage, I didnt like that brown anymore. Then I added white edge molding to the outside corners of the cage. Looks great now.

DaveDragon
07-16-2007, 04:11 PM
How about some updated pictures?

JC
09-12-2007, 08:11 AM
Nice cage
Measure twice cut once are words to live by man.
True carpenter
Linoleum adds a great touch I used this same idea a few years back in a tortoise hut.
Makes cleaning simple.
Nothing cooler then a pimped out cage and a cool reptile in it.
JC
Planet Reptiles

spencer
09-30-2007, 04:14 PM
nice tut i think this may come in handy for my bts

akward_silence91
04-04-2008, 12:27 AM
thats a sweet cage, but I have to say, it looks a little like a microwave. But that doesn't matter, cause its sweet. :D

BRAIN_Z33
10-29-2008, 09:20 PM
Wow cage came out very professional looking lol. Do you mind telling me where you got your vents from? I built a cage and still looking for those.

thanks

Seth
01-11-2009, 01:32 AM
Thank you! My beardie's current cage (60"L x 36"W x 18"H) is just a so-so cage, good enough to sell, but not enough to be "amazing" or "a job well done". This cage takes up too much space, so I'm going to sell it to a guy who wants to use it for his male boa constrictor and build Jack a 48"L x 24"W x 16"H.

Pikey
12-13-2009, 06:30 PM
those vents you can get at Lowe's & maybe home depot (they are exterior house vents for attics about $2 each) I'm using them on the cage i'm building too it's better to trace them out messure in 1/2 on all sides cut it out with a router or jig saw then mount one on the outside & one on the inside it looks good & keeps them away from the screen on the vents